| Anglais | Français |
| The programming
instructions are located in the 1995 T&C, Caravan, Voyager service manual, page 8P-5 1) remove glovebox door and find green programming wire behind it 2) with ignition ON, short programming wire to ground. 3) door locks will lock and unlock. Press any button on first transmitter. Press any button on second transmitter 4) at this time if you want to turn off horn chirp, press lock then unlock buttons on transmitter 3 times. Otherwise don't do this. 5) disconnect programming line from ground
|
1. Ouvrir la
boite à gants et la retirer. Retrouver un fil Vert situé derrière. 2. Tourner la clé de contact en position On (Sans démarrer) et connecter le fil vert à la terre (sur la carrosserie de la voiture par exemple) 3. Les portes se ferment et s'ouvrent - Appuyer sur l'un des boutons de la nouvelle télécommande pour l'activer. 4. Si vous souhaitez désactiver le Klaxonne lors de la fermeture des portes, appuyer sur le bouton "Fermeture" puis "ouverture" de la télécommande cela 3 fois de suite. 5. Déconnectez le fil vert de la terre. |
Date: Mar. 25, 2002
Models: 1999 - 2002 (BR/BE, DR) Ram Truck
1999 - 2002 (AB) Ram Van/Wagon
1999 - 2002 (AN) Dakota
1999 - 2002
(BR/BE)Ram Pickup
1999 - 2009 (DN) Durango
2002
(DR) Ram
Pickup
2001 - 2002 (JR) Sebring Sedan/Stratus Sedan/Sebring
Convertible
2002
(KJ)
Liberty
1999 - 2002 (LH) Concorde/Intrepid/LHS1300M
1999 - 2000 (NS) Town
& Country/Caravan/Voyager
1999 - 2002 (PL) Neon
1999 - 2002 (PR)
Prowler
2001 - 2002 (PT) PT Cruiser
2001 - 2002 (RS) Town &
Country/Caravan/Voyager
1999 - 2002 (WJ) Grand Cherokee
1999 - 2001 (XJ)
Cherokee
Discussion:
A Remote Keyless
Entry (RKE) Programming Procedures Card (Publication No. 81-170-00011) is being
provided with this Technical Service Bulletin to simplify RKE transmitter
programming on 1999 - 2002 North American vehicles. Additional copies of the RKE
publication, 81-170-00011 (Fig. 1), can be ordered from DDS Distribution
Services, LTD. Their number is 1-300-890-4038.
NOTE: THE RECENTLY RELEASED MILLER SPECIAL TOOL, "RF DETECTOR NO. 9001", SHOULD BE USED TO DETERMINE IF THE TRANSMITTER IS WORKING BEFORE BEGINNING PROGRAMMING PROCEDURES. THE RF DETECTOR INDICATES IF THE TRANSMITTER IS WORKING, NOT IF IT IS PROGRAMMED TO A VEHICLE.
DaimlerChrysler North American Remote Keyless Entry Programming Procedure
 |
 | ||
| AB 56045191AD* W/WO RAMS HEAD |
WJ (GRY) 58036860AD* |
WJ, XJ (BLK) |
JR, LH, KJ 04602260AA* |
 |
 | ||
| RS 645??797AB* |
PL (GRY) 0475???8AE* LH 0460??6?AC* (PRE 01 ONLY) |
DR, NS, RS |
AN, DN, BR, BE 56045497AC* W/WO RAMS HEAD* (99-00 only) |
| *Note:
these part numbers were very hard to read on my copy of the
bulletin. They may not be correct. If you need to replace a FOB, see your dealer for the correct numbers. | |||
| RKE Programming Procedure - Letter Indicates Programming Method | |||||
| Vehicle Name |
Current Platform |
1999 Programming Method |
2000 Programming Method |
2001 Programming Method |
2002 Programming Method |
| Sebring Stratus |
JR | - | - | A or C | A or C |
| Concord Intrepid LHS 300M |
LH | A or C | A or C | - | - |
| Caravan/ Voyager T&C |
NS | - | - | A or C (3BTN) & (5BTN) |
A or C (3BTN) & (6BTN) |
| Neon | PL | B or C | B or C | B or C | B or C |
| Prowler | PR | A or C | A or C | A or C | A or C |
| PT Cruiser | PT | - | B or C | B or C | B or C |
| Ram Van | AB | C or D | C or D | C or D | C or D |
| Durango & Dakota |
AN/DN | B or C | B or C | A or C | A or C |
| Ram Truck | BR/BE | B or C | B or C | B or C | B or C |
| Ram Truck 1500 |
DR | - | - | - | A or C |
| Jeep Liberty |
KJ | - | - | - | A or C |
| Grand Cherokee |
WJ | C (BL)&(GRY) |
C (BL)&(GRY) |
C (BL)&(GRY) |
C (BL)&(GRY) |
| Jeep Cherokee |
XJ | C | C | C | C |
|
DO Reprogram all of the vehicles transmitters at the same
time. NOTE: If equipped with VTSS, the system must be disarmed and/or unlocked to enter program mode. Warning: Simultaneous programming of multiple vehicles
should be avoided as any transmitter | |||||
DaimierChrysler North American Remote Keyless Entry Programming procedures
NOTE: PLEASE READ INSTRUCTIONS FULLY BEFORE ATTEMPTING TO PROGRAM TRANSMITTERS.
Program Method A (Customer Program Method)
1. Press (LOCK) button 5 times at 2 second Intervals to resynchronize transmitter, Attempt to function transmitter, If working as designed discontinue programming.
2. Turn ignition to run position, (Allow Ignition chimes to stop).
3. Using any original (working )transmitter, press the [UNLOCK] button for 4 to 10 seconds.
4. Within the specified 4 to l0 seconds, continue pressing the [UNLOCK] button and press the [PANIC] button for 1 second and release both buttons (AN/DN release either button first). A chime will sound to indicate that the transmitter programming mode has been entered (allow 3 seconds for chime to sound).
5. Press [LOCK] and [UNLOCK] buttons simultaneously for 1 second and release (a short chime will sound for AN/DN).
6. Press and release any button an the same transmitter and a chime will sound after successfully programming the transmitter (locks will cycle for AN/DN).
NOTE.- (FOR DR ONLY) A CHIME WILL NOT SOUND ON STEP #6 FOR THE FIRST TRANSMITTER PROGRAMMED, BUT WILL SOUND UPON PROGRAMMING THE SECOND TRANSMITTER.
7. Repeat steps 5 through 6 to program additional transmitters.
8. Turn ignition to OF:F position. Transmitter programming mode will discontinue after 60 seconds (30 seconds for AN/DN and RS). (All transmitter programming must be completed within time specified).
Program Method B (Customer Program Method)
1. Press [LOCK] button 5 times at 2 second intervals to resynchronize transmitter. Attempt to function transmitter, it working as designed discontinue programming.
2. Turn ignition to the run position (Allow Ignition chimes to stop).
3. Using original transmitter, press and hold the [UNLOCK] button on the transmitter for between 4 and 10 seconds.
4. Continue to hold the [UNLOCK[ button and press the [PANIC] button. A chime will sound to indicate that the transmitter programming mode has been entered (Allow 3 seconds for chime to sound).
5. Press a button on all transmitters to be programmed into the system including any previously programmed transmitters; a chime will sound when each transmitter has been programmed.
6. Turn the ignition to OFF position to exit the transmitter programming mode.
Program Method C (Dealer Program Method) *Can be used for any type transmitter.
1. Press [LOCK] button 5 times at 2 second intervals to resynchronize transmitter. Attempt to function transmitter, if Working as designed discontinue programming.
2. Turn ignition to the run position (Allow ignition chimes to stop).
3. Plug DRBIII to vehicle's 16-way data link connector.
4. Follow Service Manual and DRBIII Instructions to program transmitters.
Program Method D (For use with AB vehicles not equipped with VTSS only)
1. Locate the dark green program enable wire connected to pin #1 of the 16-way data link connector under the left side Of the Instrument panel.
2. Connect the program enable more terminal to a good ground.
3. Insert the key into the ignition and turn the ignition switch to the ON position. The power locks will cycle (Lock and Unlock) indicating that program mode has been entered.
4. Using the transmitter to be programmed, press either [LOCK] or [UNLOCK]. The power locks will cycle indicating the transmitter has been programmed successfully.
5. Repeat step 4 to program additional transmitter.
6. Disconnect the program enable wire from ground to exit program mode.
7. Turn the ignition to the OFF position and remove the key.
NOTE: REFER TO DAIMLERCHRYSLER MD82 SYSTEM OR PARTS DEPARTMENT TO OBTAIN THE CORRECT PART NUMBER AND REVISION FOR SPECIFIED VEHICLE.
Policy: Information Only
Thanks to David Lovell for supplying this TSB information
|
|